Oilfield drilling mud Hunter-MG3 shale shaker for drilling mud removal
Aipu Hunter-MG3 shale shaker is the first defense of drilled solids during well drilling. Actually, the shale shaker can not be only used in oil well drilling but also the HDD or piling desanding, the TBM, CBM and so on. Hunter-MG3 Shale shaker is a great equipment to process drilling fluids.
What detail specification of Hunter-MG3 shale shaker?
Hunter-MG3 shale shaker is linear motion shaker and capacity is over 110m3/h. When operate shaker in daily work the gravitational force of vibrators is up to 7.0G. The feeder box is top open with the cover bolted well. But the inlet port is usually at box wall center but close to bottom. There is a division line at the feeder box base and controlled by a hand break butterfly valve. The division line helps much on flow direction control, especially when we need to change the screens
The weir structure effectively reduces the impact force of drilling fluid onto the screen and enables the drilling fluid to evenly spread over the screen surface.The submersible bypass valve can easily open and close the silted feeder bottom.
Screen panels for Hunter-MG3 are framed type. They can be steel frame and composite frame. The color of screen panels can be yellow, green, and orange. Usually, the motors are Martin brand, while some are OLI or Ital-Vibras brand according to clients' preference and actual demand. The shaker deck angle adjustment is ranged -1~+5°. During operation, the deck angle is adjusted accordingly based on drilling mud condition, the cuttings condition, and flow rate situation
Specification on Hunter-MG3 shaker
| Flow rate | 110m3/h |
| Vibration mode | Linear |
| Motor | 2.5HPx2 |
| Screen panel | 3 panels |
| Screen area | 2.04㎡ |
| Deck angle | -1o~+5o (Customizable) |
| Feeder box | Mounted and top open with flange inlet port |
| Deck number | 1 |
| Base | Single deck or dual tandem, triple tandem (Customizable) |
| Electrical system | 220-415V/50Hz,220-460V/60Hz, 3Ph |
| Color | Cyan, blue, orange, red, yellow, green, etc.
|
Hunter-MG3 shale shaker flow rate
It's up to 110m3/h. The high efficiecny and the great separation effect surprise many clients.
Uphill angle will help to get discharge drier, downhill angle will help to get flow rate increased since the mud flow velocity is higher.
Other design or option on Hunter-MG3 shaker
We treat the Hunter-MG3 shale shaker as the original and initial shaker.
Another different design is feeder box inlet port position. We usually set it at bottom side close to the feeder box base. But it can be set at center or higher according to client's preference. Of course the internal structure may vary if ncessary.
We provide customzied option on color, too. According to our record recently, most of our clients select AIPU cyan. It's rather marked and beautiful. For screen panels, we can make it steel frame or composite frames. If clients request, they can be the corrugated pattern.
Besides common dual tame shaker, we produce the double decked dual tandem shaker, too. Now the users ordered Double decked dual tandem shaker are very happy with our shaker quality and performance.
Do you need Hunter-MG3 shale shakers? Please trust AIPU will be your ideal partner on shaker solutions and solids control.
Why Aipu Hunter-MG series shale shaker?
Besides the Hunter-MG shale shakers, there are Hunter-D shakers. Difference is the screen installation way and screen area. Why clients select AIPU continuously?
High-quality with good performance. True cost-effectiveness. Many of our clients are introduced by our regular clients. And among the orders, almost of them are repeat orders. Clients’ repeat orders tell many things and all of our users are satisfied with our shakers quality and our service
Now these shale shakers under manufacture are for oil well drilling solids control. Some are ordered along with whole system, some are just single separated equipment
Product Tags:
|
|
Hunter-MG3 Vibration Motor Solids Control Shale Shaker Images
|
